코엔원

• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Fix a Loose Door Hinge

Fixing a door window hinge fix that is loose can be a manageable task for most homeowners. If, however, the holes for screws are smashed and won't hold screws you may need to put in wood glue and dowels before you can put back the hinge.

Before you do that though you should clean off any the surface rust. This will help the dowels stay in place and give them a solid base to rest on.

Remove the Hinges

A lot of door hinges are able to be removed, making it easier to move the door from one side to the next or to take the entire door off the frame if need be. Anyone with a little patience can take the hinges off, but you need to know what to do.

If the hinges have been painted it is necessary to remove the paint before you attempt to remove the pins. You may scratch your door if don't take off the paint. Place the hinges in an stainless steel pot and fill it with water to the point that the hinges are submerged. The hinges should remain in the pan for about 30 minutes. The heat from the water will soften the paint making it easier to remove.

After the pins have been loosen and the pins are loose, you can take off the hinges from the frame and door. It is possible to use a standard screwdriver, however it is recommended to use a magnetic screwdriver for this project. This type of screwdriver has been specially designed to pick up metal screws and assist you in getting the task accomplished much faster.

It is a good idea to spray lubricant onto the hinges prior to trying to remove them. A simple lubricant can make the process to go more quickly and aid in the removal of the pins and screws. This kind of lubricant is able to be found in most hardware stores and home improvement shops.

The number of hinges needed will also differ based on what type of door you have and the way it's installed. Heavier and solid-cored doors will require more hinges while hollow-cored and lighter doors might only require two or three hinges.

It is also crucial to understand the different types of hinges so you can decide which one will be the most effective for your particular situation. The hinges on the exterior are designed to support the weight of the door and interior hinges have to be able to handle lighter loads.

Reattaching the Hinges

Over time, the hinges of doors may become loose and start to hang crooked or sag. It can be a big issue, but the solution is usually quite simple. A simple tightening can solve the problem. If the screw holes have been ripped out, it could be difficult to do. A wood dowel could be used to tighten these holes once more.

Begin by drilling out the hole you had previously made using an appropriate drill bit close to the size of the new screw (typically 3/8"). Fill in the hole using wood glue and a wooden stick. To ensure a secure fit, the dowel should be cut at the same length as the screw. Reinstall the screw and tighten it until you are satisfied with the degree of tightness. If the door does not stop bind up, you can insert another dowel into the gap. Repeat the procedure. Be sure to shut the door slowly in order to check the perimeter clearances after each adjustment.

Another option is to utilize the wood plug instead of dowel. It works just as well but might take a little longer to install. You can tap in a piece of wood which has been cut to the right size. If you don't own an instrument for woodworking or toothpicks, you can make use of toothpicks or matchsticks made of wood.

Make use of a countersink in order to make the hole smaller for the head of the screw after you have put it back in place. This will stop the screw from rubbing against the edges of the doors as they are closed and opened. This will make it easier to tighten the screw prior to reinstalling the hinge.

Once you have reinstalled the hinge, make sure to grease it using a dry lubricant to help keep it from getting stuck in the future. You can use products such as PB Blaster and Liquid Wrench. Apply a thin coat and give it approximately 15 minutes to get into the barrel of the hinge.

Refinishing the Hinges

If you're not yet ready to replace hinges, you could try a few easy fixes. Verify that the screws that attach the hinge plate to the door frame and frame are tight. If they're loose, tighten them using an electric drill or screwdriver. Be careful not to tighten your screws so tight that they begin to create gaps in the trim joints or, even more damagingly cause threads to be stripped.

If you're experiencing issues because the hinge plates are separating from the jamb and door, you can reattach them by gluing wood glue to the back of the plates and then inserting toothpicks or wooden dowels into the holes. The toothpicks and dowels provide an solid foundation for the screws, and prevent the plates from shifting as you push them in. Let the glue dry before reattaching the hinge.

The screws can also be smashed or gone. This can be corrected by replacing the screws. Be sure to use a drill bit that is compatible with the size of the screw hole to avoid drilling into other parts of the jamb or hinge.

Close the door once you have reattached your hinge and examine the gap between the frame and the door. It should be about the thickness of a nickel all around or less if there's an existing gap caused by a door that hung improperly. If the hinges were installed correctly, this shouldn't be a problem.

If you notice that the hinges remain loose, try putting an extra thicker shim between the hinge plate and the mounting surface to add some extra space. You can also take off the window hinge fix pin, then pound it down with a hammer in order to tighten it, or install a new hinge. You can also lubricate your hinges using mineral oil or jojoba in order to reduce friction and hold them in position. Lubricating your hinges regularly can aid in keeping them from becoming stiff or squeaky and will also prolong their lifespan.

Cleaning the Hinges

A hinge's continuous movement causes friction hinges for upvc windows, which attracts dust particles. Without periodic cleaning and lubrication, the particles become stuck in the moving parts of a hinge for doors and then build up over time. The hinge will get stiff and creaky, and its appearance could rapidly diminish. Regular cleaning, lubrication, and inspections will maintain the quality and function of hinges on a door.

Examine the hinges for signs of the accumulation of rust. If the rust has corroded to the point of destroying surface of the barrel or screw holes, you'll need to replace the hinges. If you are able to save the hinges, remove any loose rust by using wire brush and steel wool. Apply a commercial rust-removing solution or homemade solution like lemon juice on the hinge. Let the solution that removes rust sit on the hinges for a few minutes to penetrate and dissolve the remaining rust.

If you don't wish to spend time and money to replace hinges on upvc window hinges, simply tightening the screws can make the hinges functional again. It is possible to add a wooden shim or dowel to the hinge if the screw holes have been degraded. Wooden dowels are round pieces of wood in the form of rods which are available in varying sizes and lengths. You can purchase them online, in woodworking supply stores and at home improvement stores.

You can also create an shim using metal or plastic depending on the type of double glazed window hinge you are using. To make a dowel cut an unfinished dowel into the desired length. You can then dip a dowel into carpenter's adhesive and then insert it into the hole. The glue will hold the dowel firmly in place.

Before you begin cleaning the hinges, lay down a paper or cloth towel to shield floors and other surfaces from drips and spills that could happen. After securing the area then clean the hinges using a soft sponge or a cloth that has been dipped in mild cleaner to get rid of dirt, grime, and tarnish. You can use a toothbrush or small brush to reach hard-to-reach spots in tight spaces and crevices.