코엔원

• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Cat flaps let your cat go in and out at their own pace, without having to let them in or out. They also can help stop your cat from urinating inside the home.

It is much easier to put an animal flap on a upvc panel than on a glass one however, you'll require some expertise and correct tools.

Measure the Door

The installation of a cat flap inside the door can be a challenge but as long as you select the right kind of cat flap be patient and follow the instructions provided it shouldn't be too difficult. We will demonstrate how to mark the shape and use an jigsaw to cut the door area. Then we'll complete the job by affixing the flap. This will ensure that the flap is in place and also protects the doors from the damage caused by wind and rain.

To determine the size of the cat flap that you require, take a measurement of your pet's width. This will ensure that the flap is large enough that your pet can go inside and out of the house without needing to open and close the door each time, yet small enough to keep them from going too far in either direction.

If your kit comes with an illustration of the location to drill, you can stick it on the door, and then draw a pencil around it. If your door has a sill or moulding on the bottom edge ensure that you have clearance from these as this will keep your cat safe and stop them from gaining access to your home.

Next put on your eye protection and dust mask. Then using a jigsaw begin to cut along the line you have pencilled in, but don't push the blade too hard, as this can cause it to cut faster than you would like it to. Utilize a set square to ensure that you are cutting the material properly and that the cut is a rectangle. When you are happy with the result, you can remove the remaining door material.

Draw a Line

The cat flap is a great method to let your pet out and in without having to worry about them being in the house with guests or leaving unwanted gifts inside the house. It also helps prevent draughts and helps keep your home's temperature in check. Installing a cat flap on your door may seem daunting to those who haven't tried it before. A lot of people will hire a professional carpenter or joiner to do the work. While this is certainly an option, it's possible to do the work yourself if you have the appropriate tools and follow the instructions carefully.

This is much simpler to do on doors made of wood, however it is possible with uPVC. However you should be cautious not to damage the doors as this could cause the door to be damaged and invalidate your warranty. First, you need to examine the door's measurements to ensure that it can accommodate the new cat-flap. If you have an ordinary uPVC panel, this should be easy. However, if your door is made of composite or another kind of door, you might require more care.

The next step is to measure the height of your cat's stomach. This is the distance from the floor to the underside of the cat's stomach and you'll need to find a place on the door where this measurement will fall within the range your cat can comfortably pass through. Once you have the information you'll need to mark the area with a spirit-level and a pencil so that you know the hole will fit your cat.

Once you have marked out the area, it's time to cut out the hole. You will require the jigsaw, and it is crucial to take your time in order to ensure that the cuts are clean and smooth, rather than uneven and rough, since it could cause damage to your door. You should also remember to wear safety glasses and a dust mask when using the jigsaw, since dust from the saw could be hazardous to your health. Once you have completed the cutting process, you will need to smooth out the edges of the hole using sandpaper, so that your cat flap will fit easily.

Cut a hole

The process of fitting cat flap in upvc door panel a cat flap into an existing door panel or double glazing sealed unit is quite difficult. You might be tempted to tackle the job yourself, but unless have a lot of expertise in DIY, it's recommended to hire a professional to do the task for you. A botched job may not only be unsightly but it could also be an enigma for security as well as allowing cold air to get in when the cat is outside, and hot air to escape inside.

The first thing you need to do is mark the location of the hole in the door with pencil and a spirit level. This will ensure that it is properly positioned and that it runs in a straight line with the other parts of the door. Make sure to have sandpaper to smooth any rough edges.

Wear the safety equipment you require when working with a power tool. If you're worried about noise, you can buy a cordless jigsaw which is more quiet and easy to use.

You should only remove the material required to fit the flap. A little bit of extra material is required to increase the thickness of the the flap, but removing more than that could cause issues and damage the doors frame.

A door made of upvc could include a metal frame, or panel that will interfere with the microchip cat flap, and if this is the case, you'll need to make an over-sized hole to ensure that the metal doesn't come into contact with the the cat flap. If this is the case, it is important to fill in the gap and seal it with water.

If you're planning to install a cat flap in a upvc or double glazing cat flap-glazed window cat flap with metal frames it is necessary to speak with an expert. They can provide you with a new piece of glass with the hole already pre-made for the cat flap. This is less expensive than trying to install a cat flap in an existing pane of glass that wasn't designed specifically for this purpose.

Fit the Flap

Cat flaps allow your pet the freedom to move around anytime they want, allowing them to relax at home whenever they want to. However, if you own an uPVC door, it may be difficult to put in an animal flap, especially in the absence of glass panes that can be cut for one. Luckily, if you're happy to purchase and install a replacement half-glazed uPVC panel, then it's possible to fit a cat flap to the doors. It's not just a matter of drilling holes in the door. It is also necessary to do a few things to ensure that it is safe.

A uPVC, GRP or composite door panel usually has a flimsy plastic outer skin joined to a soft polystyrene insulating core. The material is fairly fragile and care must be taken when cutting through it to avoid damaging. This kind of door typically comes with a template drawing that you can use as a reference to cut the hole into your door.

After you've marked the position of the hole in your door, it's time to fit the cat flap itself. You can pick from a variety of models, ranging from simple push-button units to microchip activated ones that only let your pet in. However, regardless of what kind of cat flap you pick, it's crucial to ensure that your cat flap installation near me can use the flap and not get trapped outside in bad weather.

It is a good idea to select circular fittings rather than one that is square, since circles are more securely cut into the door glass. This is because square holes make glass more vulnerable to cracking if a drill is used on it. This is also a safer choice, as you won't have to drill into the toughened glass, which could break and cause harm to your pet or family members. This is especially crucial if you have elderly or children living in your home that might be injured by glass shards.