코엔원

• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Repair French Doors

French doors are a beautiful feature of a home they connect outdoor and indoor spaces. However, they can experience issues over time that require immediate attention for both safety and practicality.

Misalignment, sagging and warping of the sash and frame of the door are all common issues. Many of these issues are easily solved with some time and effort.

Misaligned locks

Some doors can be slack or awry due to humidity or wood swelling, or house settlement. This can make the lock bolt or strike plate sit askew which requires more force to open and close the door. This also puts extra strain on the lock, which can eventually result in mangled inner-lock components or broken locks altogether. This is a common issue which can be solved with DIY techniques.

In some instances it is possible that a small amount of lubricant might be all that's needed to make the door easier to open and close. You can use graphite lubricant, but be careful to select one that is safe for your door. Make sure to wipe the area with a damp cloth to clean any debris from around the door before you apply the grease.

A door that hangs off-center can be easily fixed by adjusting and loosening the hinges until they are aligned with the frame. However, be cautious not to over tighten the screws since this can cause damage to the door or hinges.

If your exterior French door isn't closing correctly it could be a sign there are obstructions in the lock mechanism. Most often, this is caused by short factory screws that loosen as time passes. Replace the screws with longer ones to grab more wood from the door frames.

You could also try adjusting the lock, but it will be more difficult and complicated. Begin by loosening either the lock knob or handle using flathead screw. You can then remove the lock from its cubbyhole, by unscrewing and taking it out. Look for obstructions, and then reassemble it and make sure that all screw connections are tightened.

If the latch does not hit the strike plate, you might need to move the strike plate or increase it. If the strike plate is either higher or lower than the hole for the latch it can stop the lock from closing and require a locksmith expert. If the hole is small you can make use of a file made of metal to increase the size of the hole.

Sagging

If your doors sag or have gaps, it will reduce the energy efficiency of your home. These gaps can also cause drafts and block your view. Fortunately, there are a few simple fixes that can help resolve these problems.

To begin, tighten your hinges to ensure they're properly aligned. This will take about 10 minutes or less, and will not require any tools. If this does nothing to fix the issue then you'll need to replace the hinges. They're likely to be at the end of their lifespan.

Over time, your French doors may become loose due to the weight. To prevent this ensure that you tighten all hinges on your door and check them regularly to ensure they're secure. Occasionally, you should also grease the hinges with a spray of lubrication to prolong their life.

The hinges that are old or damaged can cause doors to bow, so replacing french doors with windows hinges with new ones can aid. A new doorknob, or doors that have been freshly painted, could also alter the alignment of your French doors.

Other causes of sagging include foundation settlement, wear on hinges or improper changes made to your doors. A door that is sagging could be fixed by adjusting the hinges, tightening the hinge screws, or even replacing the hinges entirely.

It is also necessary to check the weather stripping and door sweep frequently to ensure they are working correctly. If they're not, then removing them and replacing them could fix the issue.

Also, you should check your door frames for signs of warping or rot. These issues can lead to drafts, and they will not only reduce the efficiency of your doors, but they could also cause water leakage and other damages around your home.

If your doors are sliding and you've tried the first two solutions It is likely that you'll have to smooth down the jamb of your door with a hand plane, advises Popular Mechanics. To do this, remove the doors from their hinges and place them flat on a sawhorse or something else that is sturdy. Note the areas that require planing, then use a hand plane to smooth these areas of the doorjamb.

Leaks

French doors with large glass areas are susceptible to leaks, particularly in an area that experiences frequent rainfall. Untreated, these leaks may cause the frame of the door to rot and the surrounding structure. It is fairly simple to repair these leaks, and it should only take just a few minutes.

Leaks can be caused by a number of causes, including:

A broken seal

This issue can be solved by replacing the rubber seal on either side of the threshold with an entirely new seal. This will ensure that there is an exact fit and stop rainwater from getting into your home.

Water leaking through the sill

This problem can be caused a number of ways, including the lack of a sillpan or using a sill made of metal that is not watertight. If you notice that water is accumulating around your french door replacement door, you should contact the builder to install sill pans or replace window with french doors the steel sill with a wooden sill that will be able to resist water.

Obstructions

A leaky seal can cause fog to accumulate between the double panes on french door repair glass doors. This can block the view and decrease their energy efficiency. This can be fixed by replacing the existing seal with a new one that is able to keep out moisture and air.

Loose Handles

A handle that is loose could be dangerous because it could fall while you are opening or closing your French door. This problem can be fixed by tightening the screws or replacing the handle if damaged or worn.

Similarly, a track stop that's not properly set can prevent the doors from sliding correctly, leading to jams and scratches on the frames. Applying silicone caulk to the tracks or track stops can aid in solving this issue. It's also recommended to check regularly for cracks and wear on exterior surfaces of the frames and doors to ensure that they are in top condition.

Warping

A French door is a beautiful view and lets in lots of light. However, If you're not careful, your doors may begin to warp due to exposure to humidity or heat. If this happens, consider calling a handyman who specialises in repairing French doors. They can guide you on the best way of repairing your doors, and also ensure that they are safe to open and close.

If your doors are badly damaged, you may need to replace them entirely. If they're only slightly warped it might be possible to bring them back to their original position by wetting heavy towels and laying them on the affected area. Place the towels on the doors for several days or even longer until they are completely flattened.

This method is often applied to uPVC doors, but it could also be applied to wood ones if the wood is well seasoned. It is important to keep in mind that the process can be time-consuming and difficult to achieve particularly when the doors are severely warped.

The doors could warp when they are stored improperly. Avoid them from construction work that creates lots of moisture, such as plastering and decorating. They should also be stored flat on a surface and not stacked, especially when they are not finished.

Another cause of warping is the strike plate being loose. To correct this, you must take the doors off and place them on two sawhorses. The excess wood can be removed from the edges at the top and bottom of each door using a hand plane. It's important to work in small increments so you don't end up cutting too much off the doors, which could cause them to become too thin and fragile.

After the doors have been rehung screw the strike plate in the appropriate position. If the lock isn't working after this the barrel catch may be catching on the side of the frame. This is fixable by spraying silicone onto the latch. If this doesn't work the latch, it may require replacement upvc french doors.