코엔원

• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Reasons Your fiat car keys 500 Key Fob Won't Work

A fiat 500 key fob not working 500 key (http://www.stes.tyc.edu.tw/xoops/modules/profile/userinfo.php?uid=1660310) fob is a great way to open the doors and start the car. There are many reasons the key fob might stop working. This includes a dead battery and water damage, as well as issues with the receiver module, and interference.

This listing is for an NEW replacement fiat car keys cut Flip Key Remote - similar to the Ilco brand that needs to be professionally programmed by a local locksmith (click here to search for a Locksmith Search). Includes lock, unlock, and trunk buttons.

Dead Coin Battery

A dead battery is the main reason for your 500 key fob not working. Modern key fobs only have only a limited range of operation and must be within just a few inches of the vehicle to function. If you're far from your car and press the keyfob button, it will not respond, and display the message "Key Fob Not Detected".

If this happens If this happens, replace the battery in the coin-cell (Part Number CR2032) by a fresh one from a reputable brand like Panasonic Duracell or Energizer. You can find them at your local hardware store or online.

You can test the battery of your coin-cell by pressing the buttons while you are standing close to your fiat keys 500. The parking lights should light up and the key fob will operate the lock and unlock switch.

If your key fob isn't working after replacing the battery, there may be water damage which has prevented it from communicating with the module in your vehicle. Water damage can occur in a number of ways, from small splashes to submerging the fob salt water at the beach. If you suspect that your fob was exposed to water, put it in a dry rice bag to draw the moisture back out. If that doesn't work the fob might require reprogramming by a professional auto locksmith or the dealer.

Water Damage

While the fob comes with rubber seals that keep water from the chip's electronic circuit the device, submerging it into the ocean or washing it in a machine could cause water damage. Saltwater can cause the circuit board to short and then end up dying. It's not a good idea to soak the fob in water however, don't give it up if you accidentally drop it in water or fail to take it out of your pants pocket.

Take the battery off first. Clean the electronic chip using isopropyl alcohol or another similar product and dry it completely before replacing the battery. Test the fob afterward to check if it's working. If the key doesn't function then it might need to be programmed again. This is typically done by a professional or dealer auto locksmith.

If the key is more recent and has not been programmed to your car it is likely to need to be replaced completely. A professional locksmith for cars can do this job. The locksmith will require the key cut to match your car's ignition. They will also need to reprogram the fob for your vehicle's system. This is a simple and cost-effective procedure that can be completed on the same day.

Receiver Module Issues

The 500 key fob could not function because it's out of range. The remote's range is of 30 feet, so should you be too far from your car it won't respond to your commands. It can be solved by moving it closer to your vehicle until it begins responding.

If your fob won't work after replacing the coin battery, also called a "button", "watch" or "button", it may be due to a malfunction on the internal circuit board. Reprogramming the fob usually resolves this issue. You can find directions on how to do this for most automobiles by searching YouTube or reading the owner's manual.

It's possible that you need to replace the metal retaining clips that hold the coin battery in place. If they become loose, it can prevent your coin battery from being properly seated, causing your remote to malfunction.

In rare instances, the fob may become disconnected from your vehicle due to software issues or hardware issues. You can fix this issue by visiting your local dealer or auto-locksmith to reprogram your key fob. In certain instances it is possible that the software will require reinstallation into your body control modules.

Interference

Interference can also cause the key fob not to receive or transmit a signal. This can occur when the key fob is in close proximity to a radio transmitter such as a cell phone or radar detector. Other reasons why the key fob may not function include a poor connection to the buttons and internal chip or water damage.

If the key fob has been unable to function for a while suddenly or even after trying everything you can do at home to fix it e.g. replacing the battery, reprogramming, and using the spare key fob, you may have a malfunctioning receiver module on your 500. The receiver module, located under the dashboard, detects radio frequency signals from your key fob. It converts them into electronic commands that the vehicle interprets.

Fortunately, there's an easy way to reset all on-board systems in your fiat 500 car key and include the key fob. Disconnect the battery for 15 minutes, removing first the negative cable, then the positive cable. Then, reconnect the battery. This will eliminate any remaining electrical charge and restart the car's computers, which could allow you to the key fob to function again. If the issue persists you should seek out an expert technician. They will be able to determine the root cause of any issues.